Sperdifferential 45/45 Ramps and 60NM pre-Load.

Like the old ZF LSD's with the same specifications.

With lined differential plates (slip plates with lining).

Applicable to the CIH va 1.6 rear axles of Opel with 3.18 - 3.27 -…

Wheel bearing cap T.B.V Rear wheel bearing retainer.

Suitable for Opel:

∙ Manta A/B
∙ Ascona A/B
∙ Kadett C
∙ GT Classic (1968-1973)
∙ Commodore B/C
∙ Record E/D

Please check your original for the bolt pattern before ordering.

Aluminium tailpiece with vibration damper, Opel Kadett C/Opel GT (with the CIH engine).

Rubber is dried out.

Used item.

Crown and pinionset 3.89

∙ 9x35

Suitable for the Opel CIH rear axle.

∙ Ascona A/B 1.6S and up
∙ Manta A/B 1.6S and up
∙ Kadett B/C 1.6S and up
∙ Opel GT 1.9

New.

Part number Opel: 1604162

Crown and pinionset 3.67

∙ 9x33

Suitable for the Opel CIH rear axle.

∙ Ascona A/B 1.6S and up
∙ Manta A/B 1.6S and up
∙ Kadett B/C 1.6S and up
∙ Opel GT 1.9

New.

Part number Opel: 1604161

Crown and pinionset 3.44

∙ 9x31

Suitable for the Opel CIH rear axle.

∙ Ascona A/B 1.6S and up
∙ Manta A/B 1.6S and up
∙ Kadett B/C 1.6S and up
∙ Opel GT 1.9

New.

Part number Opel: 1604158

Crown and pinionset 3.18

∙ 11x35

Suitable for the Opel CIH rear axle.

∙ Ascona A/B 1.6S and up
∙ Manta A/B 1.6S and up
∙ Kadett B/C 1.6S and up
∙ Opel GT 1.9

New.

Crown and pinionset 5.28

∙ 7x37

Suitable for the Opel CIH rear axle.

∙ Ascona A/B 1.6S and up
∙ Manta A/B 1.6S and up
∙ Kadett B/C 1.6S and up
∙ Opel GT 1.9

New.

Crown and pinionset 4.22

∙ 9x38

Suitable for the Opel CIH rear axle.

∙ Ascona A/B 1.6S and up
∙ Manta A/B 1.6S and up
∙ Kadett B/C 1.6S and up
∙ Opel GT 1.9

New.

Crown pinionwheelset 4.75

8x38

Suitable for the CIH rear axle from Opel

∙ Ascona A/B 1.6S and up
∙ Manta A/B 1.6S and up
∙ Kadett B/C 1.6S and up
∙ Opel GT 1.9

New.

Wheel bearing set for rear axle Opel OHV.

Aftermarket, good quality and a perfect fit. Measurements: 30x62x21

Suitable for:

∙ Opel Ascona A
∙ Opel Ascona B
∙ Opel GT 1.1 / 1.2
∙ Opel Kadett B 1.0 - 1.1 . 1.2
∙ Opel…

Rear axle cover Mercedes Sprinter/VW Crafter (big axle).

Used.

Set thru axles for Opel A Commodore

∙ 5x120
∙ Length, measured from the front of the flange: 72,5cm (see picture)
∙ Number of keyways: 24
∙ Marked left and right
∙ Used
∙ Bearing fit: 36,5mm

Price is for the set of…

Rubber rear axle spring plate, bottom, Opel Ascona/Manta.

Used item.

Crown and pinion wheel set Iveco Daily 3.15 Ratio 13:41

New.

To be mounted on the single and twin wheel rear axles with an egg shaped cover (see last picture).

Numbers:

∙ 7186662
∙ 30001005
∙ 100-228
∙ 294279
∙ Ø…

Crown and pinion wheel set 8x38 - 4.375Mercedes-Benz Sprinter 903Mercedes-Benz G-Classe W460/W461

Volkswagen Crafter and LT Suitable for rear axle types with the octagonal cover, which is fastened with 10 bolts. Suitable for both…

Crown and pinion wheel set Mercedes-Benz Sprinter 903Mercedes-Benz G-Classe W460/W461

Volkswagen Crafter and LT Suitable for rear axle types with the octagonal cover, which is fastened with 10 bolts. Suitable for both single and…

Crown and pinion wheel set Iveco Daily 4:22 Ratio 9:38, new!

To be mounted on the single and twin wheel rear axles with an egg shaped cover (see last picture).

∙ Numbers: 7188725 - FT62418
∙ 17256170 - 7185840 - 7185842 -…

Crown and pinion wheel set Iveco Daily 2,916 Ratio 12:35

New in box.

For use with the single and twin wheel rear axle with an egg shaped cover (see last picture).

∙ Reference numbers: 7188227 - 294662 - 7186886 - 13616 -…

Bracket for stabilizor bar rear axle Opel Ascona/Manta A, Manta B1.

One rubber, and one bolt with hub NOT present.

Used item.

Left torque arm, torque rod for rear axle Opel Ascona/Manta B.

∙ Drivers side
∙ Length from bolt hole to bolt hole is 41,5 cm
∙ The rod goes from the bodywork to the rear axle
∙ Tab present where the handbrake cable fits…

Oil seal TBJ2W14-NS.

∙ 1.734
∙ 2.567
∙ 0.484

Width 12,98mm.

Crown/pinion set Ford Transit.

Suitable for both single and twin wheel rear axles.

New aftermarket HTV crown and pinion set.

∙ 41:11
∙ 3,727
∙ Crown wheel 41 teeth
∙ Pinion wheel 11 teeth
∙ Diameter crown wheel…

Crown/pinion set Ford Transit.

Suitable for both single and twin wheel rear axles.

New aftermarket HTV crown and pinion set.

∙ 43:11
∙ 3,90
∙ Crown wheel 43 teeth
∙ Pinion wheel 11 teeth
∙ Diameter crown wheel…

Mercedes Sprinter/VW Crafter twin wheel rear axle.

Revised.

We mounted new:

∙ Hand brake lining
∙ Wheel bearings
∙ Wheel studs
∙ Brake discs
∙ Brake caliper plates
∙ Crown/pinion wheel set
∙ Bearings…

Nozzle for a Haldex computer Volvo/VW/Landrover.

∙ number: 22.100 220
∙ S727 B23
∙ 12.100 449
∙ DH 31 0256C
∙ 0373
∙ 102727

Used item.

Haldex computer for Volvo.

∙ Needs to be 'learned in'
∙ PDR AL230 AE
∙ Date stamp: 2011
∙ Used item.

Brake lining for Opel Kadett C.

∙ Left and right
∙ Number 688144
∙ Brand: TRW
∙ Round: 20 cm
∙ With of lining: 29.4 mm

Used item (only tried once).

Ingoing gear rear axle Opel Kadett C, (type with OHV engine).

∙ Opel Kadett C
∙ Only type with OHV engine
∙ 22 teeth

Used item.

Thru axle for Opel Kadett C 1.2 (type with OHV engine).

∙ 4 x 100
∙ length 67,5 cm
∙ Used item.

For logistics: no 817.

Thru axle for Opel Commodore B (5 x 120).

∙ 5 x 120,
∙ length 75 cm,
∙ used item.

For logistics: no 935.

Crown and pinionwheel Opel Ascona/Manta B.

∙ Ratio 9:31 (3.44) ,
∙ GM number: 8932741
∙ Used item
∙ Matching numbers.

For logistics: no 7241.